Designed to meet the rugged demands of Australian conditions and delivering multiple source charging for DC systems.
The Enerdrive ePOWER DC2DC Battery Charger is a fully automatic multistage, multi input battery charger with the ability to charge from either an alternator linked to a battery; or via solar power with the in built Maximum Power Point Tracking (MPPT) Solar Controller.
Enerdrive ePOWER 24V – 30A DC2DC Battery Charger
- Two totally independent DC Inputs for both engine and solar regulation charging one house battery bank output
- DC M6 screw terminals that will allow for large battery cable connection between all sources
- A dedicated Maximum Power Point (MPPT) solar regulator
- The same battery algorithms as included in our AC mains ePOWER battery charger including a specific lithium charging profile
- 30A output up to 40+°C with thermo controlled fan cooling
- Fully programmable LCD display to show which source is charging the battery along with charger status, voltage and amperage
- Temperature sensor included in charger for more accurate battery charging
The Enerdrive ePOWER DC2DC Battery Charger is a fully automatic multistage, multi input battery charger with the ability to charge from either an alternator linked to a battery; or via solar power with the in built Maximum Power Point Tracking (MPPT) Solar Controller. With two inputs available, the house battery will be charged from either the engine while underway, or via the solar panels when stationary. The process to choose either engine or solar is fully automatic and both functions are controlled from within the unit itself without the need for external relays.
During normal operation the ePOWER DC2DC Battery Charger will do a full charge cycle to float stage on the house battery bank with ability to choose either GEL, AGM, Flooded, Custom Programmable or Lithium. Once float stage is reached the charger transitions to a power supply mode to support any on-board DC loads.
Multistage Charging Process
The ePOWER DC2DC Battery Charger is a fully automatic, set and forget charger. It is designed to quickly and accurately recharge your deep cycle batteries utilising charger algorithms that help to maximise the life of your specialised deep cycle batteries.
The ePOWER DC2DC Battery Charger features multistage smart charging technology that enables the charger to be connected to your battery banks permanently. With the input of multiple sources, you can be assured of charging your batteries whenever underway; or when the sun is shining on your solar array.
As dictated by battery manufacturer’s recommendations, deep cycle batteries require a multistage charge sequence for perfect, fast and accurate charging. The Enerdrive ePOWER DC2DC smart charger delivers three primary charge stages.
Stage 1 – Bulk or Boost charge; The battery is charged at full rated output current of the charger until the battery reaches its final charging voltage, known as its absorption voltage. In this step, around 80% of the battery is recovered as fast as possible.
Stage 2 – Absorption Charge; With the charger voltage held steady, the remaining 20% is replaced with the charger allowing the current to taper off as the battery approaches full charge.
Stage 3 – Float; Finally, in the float stage the charger voltage is lowered and held at a constant and safe predetermined level. This prevents the battery from being overcharged, yet allows the charger to supply enough current to make up for the self-discharge losses of the battery, while supporting any additional loads connected to the battery (such as DC lighting and refrigerators). This stage allows for the charger to be used as a DC power supply.
|Output Voltage||24V Nominal (17.0V min)|
|Output Current (Maximum)||30A|
|Charger DC Output (CH1):|
|Selectable Battery Type||Gel, AGM, Flooded, Lithium, Program|
|Charger Voltage Range||27.6V – 31.0V|
|Float Voltage Range||26.0V – 27.6V|
|Charger Current (User Selectable)||5 / 10 / 20 / 30A (default 30A)|
|Equalize Voltage (Flooded Battery)||31.0V|
|Equalize Charging Current||10% of Bulk Current Setting|
|Charging Control||2 stage / 3 stage selectable (Default 3 Stage)|
|DC Output Bank||Single|
|Current draw from CH1 when not operating||= < 50 mA|
|Battery Temperature Setting||Low/ Normal/ High (Battery Temperature Sensor Standard)|
|INPUT Rating (CH2 – MPPT Solar)|
|Input Voltage||14.5 – 45VOC|
|Maximum Solar Input||≤23V input, 500W (600W allowable) ≥37.5V-45V input, 800W (1000W allowable)|
|INPUT Rating (CH3 – Start/Alternator)|
|Input Voltage||10.5 – 16VDC / 21 – 32VDC|
|Height x Width x Depth||242mm x 172mm x 74mm|
|Unit Weight||1.85 Kg|
|Shipping Weight||2.17 kg|
|Note: Specifications subject to change without notice.|